The Anvil Mustang is a successful collaboration of design ideas and talents between Pure Vision and Anvil Auto. The project began as a vehicle to develop and showcase a new line of 1969 Ford Mustang parts for Anvil Auto. What it has become far surpassed everyone’s expectations. It has won many prestigious awards and is featured in the “Fast And Furious 6” movie and continues to gain in notoriety with a spread in Hot Rod Magazine.
Anvil's 1969 Ford Mustang
The following carbon fiber parts were developed by Anvil Auto and Pure Vision: Custom hood with functional air extractors, front bumper, front spoiler, front fenders (widened by 1 1/8”), custom cowl panel with recessed wire mesh vent opening, deck lid, rear quarter extensions, flush bumper, custom 3 pc. rear spoiler, driver’s and passenger’s dash inserts. Modifications to the stock sheet metal performed by Pure Vision are numerous, albeit, subtle. Like all Pure Vision creations, the goal was to enhance the original body lines without spoiling them, while adding details that have purpose. Here is just a partial list of some of the more significant mods. Front grille modified to eliminate inboard headlights and adding fog lights behind it. Front lower valance has’66 Corvette turn signals frenched into it and former turn signal housings modified to serve as brake cooling ducts.
Anvil's 1969 Ford Mustang with Modifications
Firewall moved back 3 ½”. The rear quarters have been widened by 1 1/2” on either side. Tail panel modified to fit ’68 Mustang tail lights and cut outs with mesh screen, Anvil icon gas cap. Back up lights removed from lower valance and “floating” PIAA lights place behind mesh in tail panel. Rocker panels modified to fit side exit exhaust. Functioning rear quarter brake cooling scoops. Door handles, wiper arms and hood hinges all lightening drilled Major amounts of steel tubing integrated into chassis, engine bay and passenger compartment for much needed stiffening. Anvil Phantom side marker lenses integrated into body work.
Anvil's 1969 Ford Mustang Rear as Modified
Front Suspension- JME Enterprises all aluminum cradle, spindles and A-arms with F1 style push rod in-board cantilever coil over shocks by JRI and Hyperco coil springs powder coated red to match interior.
Rear Suspension- Modified Maier Racing torque arm, inverted Watts link system with F1 style push rod in-board cantilever coil over shocks by JRI and Hyperco coil springs powder coated red to match interior, Speedway Engineering prepared Ford 9” rear axle housing with NASCAR full floater hubs and axles.
F1 Rear Suspension
Other- Fabricated and relocated engine mounts and transmission cross-member, JME sub-frame connectors, custom fabricated and integrated tie down strap hooks, 12 point ARP fasteners used throughout.
Aluminum Jon Kaase Racing 520 cid Boss “9” producing 805 HP
All aluminum Jon Kaase Racing 520 cid Boss “9” producing 805 hp which equals an outstanding 4 to 1 power to weight ratio, Custom Pure Vision billet aluminum motor mounts, air cleaner, spark plug wire holders, alternator bracket and remote oil filter mount, Electromotive ignition system under dash, aluminum Griffin radiator, Custom stainless headers by Resurrection by Mike using Spin Tech 3” stainless mufflers and tubing, Custom aluminum oil pan by Jeff Johnston, Modern Driveline prepared Tremic TKO 600 5 speed transmission with Quick time billet steel bell housing, fabricated bell housing cover with inlet and outlet clutch lines, Kevlar clutch, custom aluminum drive shaft, tunneled frame rail for fuel fitting pass through, hand-made fuel lines and bulkheads, Fuel Safe fuel tank with in tank pump, 12 point ARP fasteners used throughout, driveline moved back 3 1/2”.
Complete custom leather interior with wool carpet by Eric Thorsen Custom Upholstery, fabricated center dash switch panel complete with cell phone storage and 12 V power port, auxiliary gauges on dash pad, custom one-off gauges by Redline Gauge Works, fabricated mounting locations for Wilwood hanging pedal assembly, fabricated throttle pedal with splined shafts and needle bearings, fabricated dead pedal, fabricated shifter arm, shifter bezel and window cranks by White Rhino, fabricated mounts for electric heater and all under dash electronics, widened/modified fiberglass rear quarter and rear seat delete panels and related brackets to accommodate widened wheel tubs and Maier Racing suspension, fabricated battery box with integrated cut off switch, map light from late Fox body Mustang, LED courtesy lights in sail panels, roof panels and under dash, steering column shortened with roller bearings, Electric power steering motor and ESC module integrated into steering system, 12 point ARP fasteners used throughout.
Anvil's 1969 Ford Mustang Custom Interior
Baer Brakes 6S caliper custom powder coated to match interior, 14” rotors front and rear, hand-made hard lines, brake controls of pedal bias and proportioning valve and rear brake line lock at driver’s control in dash.
Wheels & Tires
Custom machined by Evod Industries patterned after 1969 Gurney Eagle Indy car; Front= 18 X 9.5 Rear= 19 X 12, shod with Michelin Pilot Sport II Front= 275/35ZR18, Rear= 345/30ZR19.
Check out our video here